hello ,i have probleme no sound output jack ,with portapack h2+ AK 4951 all firmware tested ,connected pc no sound ,portapack no sound ,icon sound yes mets not signal. pcb portapack v3.6 (ip5306 3229.16x) (wm8731LS 03AFRF5) (10.00BN D212).thanks.
vous pouriez répondre quand on vous parle ,sa s'appelle la politesse ,au lieux de supprimé mets questions,peut etre les méssages était 'il au mauvais endroit ,si ces le cas je m'en excuse .mets vous auriez pu répondre,ces quoi le problème pour que vous ne répondiez pas ?
I will make some M8Q GPS version H2 later ,if avable you can buy with discount from my patner shop,if GPS version avable i sent you a email and a link.
Good Day! I have a problem with my Portapack h2 v3.6. I put the Hackrf Portapack H2 to charge overnight and in the morning it did not turn on. I replaced the transistor in the Hackrf according to the diagram. But with Portapack H2, I don't have a repair manual, can you help me with this? On the Portapack H2, the legs that are inserted into the P28 block and have the number 1 and 3 are slightly burnt.
My H2 R4 has not been able to turn on (without constant power to it) but runs fine with power supply in.
It is not able to charge the battery (but the area affected does not appear to be too close to the charger chip IP5306), there seems to be a slightly burnt out part of the PCB board but I can't figure out what that is and if it is repairable it is near the 1R0? chip {the emblem is hard to read so name of chip I reference here could be wrong}.
Hi, I have a v3.6 PP and when I press RESET on the HackRF it crashes/freezes, the only way to recover is to reboot/powercycle. I think many v3.6 have this issue, is there any fix?
Thanks!
Hi, my HackRF has never used the external TCXO clock source. Only the internal 25MHz clock source is displayed in the settings. Which part of the Portapack should be replaced? Is it only necessary to replace the TCXO components or do I need to replace peripheral chips? What I got is a v3.6 motherboard. I am using official firmware, is it possible that there is a problem with the firmware?
hello ,i have probleme no sound output jack ,with portapack h2+ AK 4951 all firmware tested ,connected pc no sound ,portapack no sound ,icon sound yes mets not signal. pcb portapack v3.6 (ip5306 3229.16x) (wm8731LS 03AFRF5) (10.00BN D212).thanks.
I think is the H2+ problem,just Tell the Seller,Refund money back.
sorry for my probleme sound jack -why delette my méssage ,no gentil,no réponse = mal poli ,me make de pub for your pcb v3.6
vous pouriez répondre quand on vous parle ,sa s'appelle la politesse ,au lieux de supprimé mets questions,peut etre les méssages était 'il au mauvais endroit ,si ces le cas je m'en excuse .mets vous auriez pu répondre,ces quoi le problème pour que vous ne répondiez pas ?
what is your broblem?about?
h2+ 的屏幕代码有提交github吗?为什么我用了github上的1.6.0以后无法点亮
Hi, there are no 3 passive components around LB2K. How do I find out what it is and at what value?
hello friend,what is LB2K ,take a photo to me i can tell you,bg7iyn@icloud.com
Good day! Please tell me which GPS chip can be installed on your board?
https://www.mmdvm.club/index.php/h2plus.html
i add M8Q gps and try to support it
it is MAX-M8Q
Thank you! Just a chip to solder or something else to do?
I will make some M8Q GPS version H2 later ,if avable you can buy with discount from my patner shop,if GPS version avable i sent you a email and a link.
Ok! Thank You!!!
And more. What power and what resistance can the speaker be set?
0.5W-2W any speaker support it.
Thank you!
Good Day! I have a problem with my Portapack h2 v3.6. I put the Hackrf Portapack H2 to charge overnight and in the morning it did not turn on. I replaced the transistor in the Hackrf according to the diagram. But with Portapack H2, I don't have a repair manual, can you help me with this? On the Portapack H2, the legs that are inserted into the P28 block and have the number 1 and 3 are slightly burnt.
good night!,i think is the charger chip IP5306 is bad,just replace this IC,you can sent me bad pic jumbo5566@qq.com,i can see what happen.
Hi,
My H2 R4 has not been able to turn on (without constant power to it) but runs fine with power supply in.
It is not able to charge the battery (but the area affected does not appear to be too close to the charger chip IP5306), there seems to be a slightly burnt out part of the PCB board but I can't figure out what that is and if it is repairable it is near the 1R0? chip {the emblem is hard to read so name of chip I reference here could be wrong}.
I can send you photos if that helps?
Hi, I have a v3.6 PP and when I press RESET on the HackRF it crashes/freezes, the only way to recover is to reboot/powercycle. I think many v3.6 have this issue, is there any fix?
Thanks!
Yes you need a USBBlaster to update CPLD,the cheap USBBlaster works on it.
Hi, my HackRF has never used the external TCXO clock source. Only the internal 25MHz clock source is displayed in the settings. Which part of the Portapack should be replaced? Is it only necessary to replace the TCXO components or do I need to replace peripheral chips? What I got is a v3.6 motherboard. I am using official firmware, is it possible that there is a problem with the firmware?